Foolproof, dependable tester accurately tests state of charge within temperature extremes of -40° to 130° F. Uses less than 1/4 oz. of acid. Easy to use. Easy to read. Leak-proof container and pocket protector. Shipping Weight 0.10 lb.

Large 16-1/4" professional disc-type tester is accurate down to -40° F. Full size tester uses specific gravity and the number of floating discs to show state of charge. Accurate at all temperatures. Specific gravity levels are printed on the tough, see-through plastic body. Has one-piece rubber bulb, neoprene tip. Shipping Weight 0.35 lb.

Wirehawk® requires just one hand to test circuits in hard-to-reach areas. Works two ways: Captures and pierces wire with unique hook tip design or can be used as an “ice-pick” type tester. If circuit is live, bulb in handle lights up. Has 16 gauge, 44-inch ground wire with 50 amp clamp. Use for circuits, connections, fuses and 2-cycle engine timing. Available for 12V or 24V circuits. Shipping Weight 0.30 lb.

Supplies power or ground to test operation of electrical motors, solenoids and more by supplying power or ground. For 12V or 24V systems. Safe (in test mode) for computer circuits. Red or green LED shows polarity at probe.Shipping Weight 0.80 lb.

Nickel-plated steel adapters snap on to terminals. No need to remove cables. Fits all OEM replacement terminals. 500 amp capacity. Shipping Weight 0.20 lb.

Works on ignition systems from high energy electronic automotive systems to small engines. Tests for no start conditions and for spark strength. Adjustable gap allows for spark gap requirements from 0 to 40,000 volts. Gauge background makes spark easy to see for accurate measurement. Alligator clip securely fastens to ground. Screw assembly adjusts spark gap quickly and easily. Includes safety shield. Shipping Weight 0.10 lb.

Allows technician to test for current drain caused by control modules, computers or other solid state devices. Attaches in-line to negative battery terminal and cable. Current drain is read by connecting ammeter across tester. Used on all computer controlled vehicles since 1980. Eliminates the “shot-gun” method of replacing suspected components. Fits both side terminal and top post batteries. Plated for excellent conductivity. Shipping Weight .50 lb.

Kit tests glass tube and blade-type fuses and fuse boxes using ATO, Mini and Maxi fuses. Accesses power source to check for voltage, opens, shorts and amperage draw from selected circuits, etc. Nylon connectors easily adapt to fuse box. Plated contacts. 12" leads. Kit includes: - ATO Fuse Block Adapter - Mini Fuse Block Adapter - Maxi Fuse Block Adapter - Relay/Maxi Fuse Removal Tool. Eliminates backprobing and other makeshift methods that can damage wiring or connector. Easy, professional way to test electrical circuits at fuse block. Shipping Weight 0.20 lb.

For ignition systems with coil-on plugs, including Ford, Chrysler, Mitsubishi, Nissan and more. Quick way to test for no-start conditions. Gap adjusts from 0 to 40kV. 12” ground wire. Shipping Weight 0.15 lb.

Boot Puller measures 5-1/4” long to reach and remove recessed spark plug boots. Tool is made of glass-filled nylon and has an angled lip to reach under boot. Pulls baked on boots without damaging plug wires.

The new tool works on Deutsch HD10, HD20 and HD30 Series connectors, plus Deutsch Jiffy Splices. Deutsch connectors are marked by name for easy identification. Kit contains six tools to fit the following wire sizes: 4, 8, 12, 14, 16 and 20 gauge. Deutsch terminals have a special security collar that the connector tabs lock against. The Terminal Removal Tools slide over the terminal collar and depress the tabs from the rear of the connector. Deutsch terminals and connectors are factory OEM on many automotive, heavy duty truck and industrial applications.

Sharp, small diameter probes slide along wire into connector to back probe circuit. No need to disconnect connector and terminal. Kit contains 20 pin-type back probes in five different colors.

This kit provides the technicians with an assortment of back probe pins which gives the technician access to the back probe circuit without any obstructions.  The new 490-M Back Probe Pins also have a longer pin to reach circuits that were previously unreachable.

The 490-M kit includes:
(10) Straight Pins
(5)   90 Degree Pins
(5)   45 Degree Pins

Sharp, small diameter probes slide along wire into the connector to back probe circuit.  Bent at 90 degrees with longer, more durable pins than the original 490 kit.  No need to disconnect the connector or terminal. 

The 490-90 Kit includes:
(20) 90 Degree Back Probe Pins in 5 different colors

Tools quickly and easily disassemble automotive connectors to remove faulty terminals. Eliminates connector damage and is easier and faster than prying connectors apart with a screwdriver.Includes seven terminal tools to fit the most common automotive connectors. Each tool has a specially designed tip to depress the connector locking tab that secures the terminal.

Terminal Kit Includes Part Numbers:

49307	49304
49308	49305
49302	49306
49303

Instructions:
Push wire forward and hold, then insert tool over the terminal in the connector and push until the tool bottoms out.  Gently pull wire out of the back of the connector.  This tool is used for both male & female terminals.

Application:Delphi weather pack connectors, both male & female

Instructions:Push wire forward & hold, the insert tool into the front of the connector over the terminal and push to release the terminal.  Gently pull wire out of the back of the connector.

Instructions:Push wire forward & hold, then insert tool into the front of the connector next to terminal & push on the release tab to release the terminal.  Gently pull wire out of the back of the connector.

Application:Use on internal release connectors with medium to large release tabs.  Amp, Deutch, Delphi, Pack-Con, etc.

Instructions:This tool is used to remove the locking tabs installed in some of the connectors.  Place the hook into the hole in the locking tab & pull to remove the tab.  Then use the appropriate terminal removal tool to remove the terminal.

Instructions:This terminal tool is designed to access the terminal from the back side of the connector.  These terminals are the Packard Pull Through- type terminals.  They are installed through the front side of the connector.  Place the tool into the rear of the connector to release tab on the terminal.  Push the terminal towards the front of the connector to remove.

Application:Delphi Metri-Pack Pull Through Connectors.

Instructions:
Push wire forward and hold, then insert tool into small slot on the front of the connector next to terminal and push until the tool bottoms out.  Gently pull wire out of the back of the connector.

Application:
Amp, Deutch, etc. connectors with latches inside/behind a locking insert.  Use tool #49305 to remove insert.

Instructions:Push wire forward & hold, then insert tool into small slot on the front of the connector next to terminal and push until the tool bottoms out.  Gently pull the wire out of the back of the connector.

Application:Delphi 56, 58, 59 series & Amp connectors using a single tab on terminal.  Also, Amp Timer Connector with single tab terminal.

 Instead of cluttering your toolbox with unused sizes of Deutsch Tools, now you can buy just the sizes you need. Tools fir Deutsch HD10, HD20 and HD30 Series connectors plus Deutsch Jiffy Splices. Deutsch wire terminals have a special security collar that the connector tabs lock against. Tools are designed to slide over the wire in the rear of the connector to release the locking tabs. Deutsch terminals and connectors are found on Chrysler, GM, AGCO, John Deere, Case, Babcat, Caterpillar, Harley Davidson, Mercury outboards, Kenworth, Peterbuilt, White and other HD applications.

3 per pack

Instead of cluttering your toolbox with unused sizes of Deutsch Tools, now you can buy just the sizes you need. Tools fir Deutsch HD10, HD20 and HD30 Series connectors plus Deutsch Jiffy Splices. Deutsch wire terminals have a special security collar that the connector tabs lock against. Tools are designed to slide over the wire in the rear of the connector to release the locking tabs. Deutsch terminals and connectors are found on Chrysler, GM, AGCO, John Deere, Case, Babcat, Caterpillar, Harley Davidson, Mercury outboards, Kenworth, Peterbuilt, White and other HD applications.

 Instead of cluttering your toolbox with unused sizes of Deutsch Tools, now you can buy just the sizes you need. Tools fir Deutsch HD10, HD20 and HD30 Series connectors plus Deutsch Jiffy Splices. Deutsch wire terminals have a special security collar that the connector tabs lock against. Tools are designed to slide over the wire in the rear of the connector to release the locking tabs. Deutsch terminals and connectors are found on Chrysler, GM, AGCO, John Deere, Case, Babcat, Caterpillar, Harley Davidson, Mercury outboards, Kenworth, Peterbuilt, White and other HD applications.

3 per pack

The tools in the Professional Terminal Release Tool Kit are made of steel & were designed especially for the professional technician.  The kit is packaged in a custom pouch and includes (3) tools for different sized wire & contacts:

Dry charge battery filler attaches to standard acid-pak tube. Features “Cell-Eye” to prevent over-filling. Ends acid spills, drips and leaks. No more burns, holes in clothing or problems. Positive thumb release valve absolutely controls acid flow. Comes with spacers to adjust cell-fill level. Full instructions included. Guaranteed not to leak or drip. Shipping Weight 0.25 lb.

Allows use of No. 604 Activator® Battery Filler to fill small batteries. Made of high strength nylon material. Shipping Weight 0.05 lb.